When measuring high-overtone quartz crystal resonances, the electrical signal path matters almost as much as the acoustic sensor itself.
Quartz Crystal Microbalance (QCM) systems operate at radio frequencies where cable properties, parasitic shunt capacitance, contact resistance, and switching components directly influence the measured acoustic admittance spectrum.
A standard 5 MHz AT-cut quartz crystal, for example, is routinely characterized not only at its fundamental resonance frequency, but at its higher odd overtones—most notably 15 MHz (n=3) and 25 MHz (n=5). In modern Quartz Crystal Microbalance with Dissipation (QCM-D), impedance analysis (QCM-I), and Electrochemical QCM (EQCM), tracking the resonance frequency shift (Δf) alongside the dissipation change (ΔD) across multiple overtones is essential for distinguishing true rigid mass deposition from viscoelastic film damping.
The experimental challenge sharpens when several sensors must share a single measurement instrument, such as an impedance analyzer or vector network analyzer.
Manual BNC reconnection is inconvenient, wears out precision coaxial connectors, and introduces mechanical cable flexing that corrupts baseline acoustic calibration. Yet introducing an off-the-shelf semiconductor switch matrix introduces nonlinear junction capacitance, leakage currents, and insertion loss directly into the resonant tank circuit.
The Smart Multichannel Relay (SMR) from DM Technologies provides mechanical signal routing with documented low-loss performance in the MHz range.
Low Insertion Loss. High Isolation. Programmable Switching.
The SMR features three independent 2×1 (SPDT) coaxial BNC channels, allowing selected signal paths to be connected through gold-plated mechanical contacts rather than semiconductor switches.
Its measured RF characteristics across the relevant frequency band include:
| Parameter | 3 MHz | 30 MHz | 300 MHz |
|---|---|---|---|
| Transmission (Insertion Loss) | −0.07 dB | −0.07 dB | −0.82 dB |
| A–B Channel Isolation | −90.0 dB | −71.6 dB | −48.3 dB |
| Contact Resistance | < 200 mΩ | < 200 mΩ | < 200 mΩ |
These values are particularly relevant when designing measurement connections for MHz-range quartz resonators:
- Negligible Damping Contribution: The low transmission loss (−0.07 dB at 30 MHz) ensures that the switching stage does not artificially lower the loaded quality factor (Q) of the crystal resonator.
- High Crosstalk Suppression: Physical contact separation isolates the unselected signal connection (−71.6 dB at 30 MHz), preventing adjacent crystals from parasitically coupling into the measurement loop.
- Zero Thermal Dissipation: Quartz crystals are inherently temperature-sensitive. The SMR employs bistable latching relays that draw power only for a few milliseconds during state transitions. Once switched, current draw is zero, eliminating localized heat generation that could cause thermal frequency drift.
- Total Ground-Loop Decoupling: When powered by its internal 2 × AAA Lithium/Iron Disulfide (Li/FeS2) batteries, the SMR operates completely detached from 50/60 Hz mains harmonics and computer ground loops.
From a Single Resonator to Automated Sensor Arrays
By interconnecting SMR channels using short external BNC jumpers, researchers can configure an automated 1-of-3 or 1-of-4 multiplexer. With USB serial control and a dedicated Python interface, SMR switching can be incorporated directly into an automated measurement sequence:
import time
from smr_controller import SMR
# Initialize Smart Multichannel Relay
smr = SMR(port="COM3")
# Sequentially route through 3 quartz flow cells
for channel in [1, 2, 3]:
smr.select_channel(channel)
# Verify physical contact closure via hardware interrogation
state = smr.get_state()
assert state.is_connected(channel), f"Channel {channel} verification failed"
# Execute multi-harmonic sweep on Impedance Analyzer (5, 15, 25 MHz)
analyzer.measure_resonance_overtones(crystal_id=channel, overtones=[1, 3, 5])
time.sleep(0.5)
This opens up practical possibilities for:
- Differential Sensing: Interleaved cycling between a functionalized sensing crystal and an uncoated reference crystal to compensate for environmental drifts.
- Multi-Channel EQCM: Sequential acoustic monitoring of multiple working electrodes within an electrochemical cell without moving delicate potentiostat cables.
- Unattended Long-Duration Assays: Autonomous multi-sample adsorption kinetics over hours or days without human intervention.
In precision resonance measurements, the electrical contribution of the complete switching network must still be characterized. Transmission loss and isolation are important RF specifications; resonance-frequency and dissipation accuracy must be established in the final setup.
The SMR brings mechanical switching and software automation together in a broadband platform for scientists building more flexible QCM and EQCM measurement systems.
Technical Resources & Inquiries
- Explore Hardware & Specifications: Smart Multichannel Relay Product Page →
- Download User Manual (PDF): SMR User Manual & RF Appendices (PDF) →
- Request an Institutional Quotation: Request a Formal Quotation →